Fabric care

Intensive cleaning of textile floor coverings

Job of cleaning it, both the superficial and the deep impurities thoroughly penetrated into the building to remove dirt particles and yet gentle.

The cleaning companies uses in the intensive cleaning of textile floor coverings two processes: the shampooing and spray extraction.
When shampooing, with which the surface is cleaned, it depends mainly on the correct choice of machine brushes. By contrast, the dirt spray extraction is obtained from the depth of the flooring.

It is this deep, it is dirt, the leaves gradually turn gray carpet and the mat. In addition to the purely visual disadvantages because the life of the pavement is considerably shortened.
By the double process during spray extraction – the intense spray the cleaner and the suction of the solution in the same operation done an extremely thorough, hygienic and yet very gentle cleaning.

Stairs

A staircase is an elegant solution to get from one floor to another, made of the footprints, the risers of the balusters and newel posts to. Learn how to fix problems like the creaking stairs.
The elevators are not a realistic proposal for negotiations of the two or three houses of the floor. The Dumbwaiters and laundry chutes used to be common, but only the scale has stood the test of time. Complex can be constructed so they are bound to have maintenance issues.
Residential components of the scale
According to the carpenter who built the ladder and if the software has been used in architectural design, the components of the scale may vary. But, these are some common terms.
Footprints. These are the horizontal components quell’fa a step above. The back goes under the riser and the top edge is rounded, protruding lower riser and is finished with the following  CONJUNCTION. Risers. These are the vertical components. We regulate and support the instruction on the lower edge of the impression than just sniffing around. Balusters. The posts also often named as they are turned on a lathe of wood, these are the posts that support the handrail. They inserted in grooved rails at the top. With the stairs of the closed-Traversal  have entered into a cross grooved at the bottom. Systems with open-Traversal  measurements of the lower part and the impression is closed in with the molding. Newel posts. This is the vertical element to the bottom end of the handrail and is usually larger and more ornate of the balusters. When children are sliding down the handrail in the old movie, this is the thing that stops us. Quickly! And painfully! Reinforcement of the blocks and wedges. These components are installed on the side of the stairs to keep fingerprints and narrow risers. Fix creaking from the tracks below
The moisture changes and wear causes the pieces of wood to move, move and settle over time and the seasons. The result is usually a creaking, but not a dangerous situation. In the best cases, repairs can be made from under the stairs. This area is usually a powder room, bathroom, closet, or where the Harry Potters of the world are designed to sleep.

Check to see if there’s loose wedges between the ends of the risers and fingerprints. Use a mallet to gently tap it back in comfortably. The blocks are not on the edges but in the field, in the center or equally distanced from the center. These can be glued and screwed back to the tracks safely and risers.
Fix creaking from the tracks above
There are times when the bottom of the stairs is not accessible. In this case, the only thing to do is to work for the above. If the leading edge of the impression separate from the lower riser, can be screwed down.
If the problem is at the back of the footprint, the angle brackets can be used to remove the riser and cover tight. This can be unpleasant, though, and can be disguised carpet or molding.

Rosenfeld and Rose Friedman of Shirtwaist Factory fire of the triangle

Replacing the balusters of the staircase
In systems of the closed-cross, these measurement in a side grooved to the bottom and is separated by spacers. Simply remove the spacer behind the bottom baluster to remove and replace the offending. If the spacer was destroyed in the removal process, a new suit.
In the open-beam systems, first remove the molding to the bottom of repression, the footprint. Then remove the spacer of the handrail in front of the auction of the railing and hit the top of the railing rod slightly (can be nailed through the handrail).

Cleaning ideas for tile

For daily cleaning of floor and wall coverings are absolutely not recommended  foCerasarda tile, aggressive products such as acids and other substances or abrasive tools (anti-limestone, sponges, etc.) will damage the tile

It is also advisable to use neutral products commercially available.

We feel that putting in contact Cerasarda tiles (with textures craquelé) with water, dirty or greasy substances and materials can ruin the effect of the surface craquelé.

For routine maintenance, clean the surface as needed using an aqueous solution obtained by placing three tablespoons FLOOR CLEANER in 10 liters of water. This cleanser is specific to clean enamel surfaces as it removes dirt without leaving any surface residues.

If you wish to proceed even to the Anti-stain (not required for routine maintenance), distribute, dry surface, a coat of Cerasarda Craquele ‘PROTECTOR, as described in the first tab.
Particularly vulnerable to stains for surfaces such as coatings and kitchen countertops, we recommend every 2-3 years to renew the anti-stain.
To perform such maintenance should clean the surface with the first Cerasarda REMOVER, as described in the first tab.

After washing, dry surface, spread a coat of Cerasarda Craquele ‘PROTECTOR, as described in the first tab.

In the case of organic and biological stains persist, apply COLOURED STAIN REMOVER (Faber Showroom) Pure spotted on the surface and leave. The contact time, from about 15/30 minutes, depending on the variety and type of stain material.

Rinse well with water and let dry. Repeat the application if the stain should further continue.

If the material had been washed with detergents at acid pH and, as a result of this washing, we were presented iridescent enamel or aggression, it is advisable to make a recovery Cerasarda Craquele ‘CREAM.

In the case of deep acid attacks, suggest that recovery is concerned with Cerasarda Craquele ‘CREAM through a random orbital machine. After using the cream, it is recommended to rinse with clean water.

.

Tile options

Anyone who has lived the experience to replace the old floors during renovation work will be ‘realized the amount of work required to make everything perfectly workmanlike.

Whether you demolish the old floor, is that it overlaps the new over the old, several problems remain, and harbingers of discomfort for those who are also in the position of having to reside in the house during the execution of the work.
 

If you opt for the demolition of the old floor and the subsequent installation of the new, we must necessarily take into account that need to dispose of the partly demolished, damage some equipment under the floor, and a whole series of other problems such as dust generation, risk water leaks in the spaces below, and the inevitable complaints tenant downstairs.

 

The second hypothesis, ie positioning the new floor, stuck on the old, is not without problems.

 

Sometimes in fact, that when you paste a new floor over an old one, if somewhere in the support of the old floor has been created over time a bubble of air that tends to lift the cover, posing problems become significant.
  
The search for new and more advanced ceramic materials has led to the registration of patents for new production systems increasingly sophisticated and practical, able to produce solutions very useful.
 

Among the many and qualified Italian companies in the industry, the Cooperative of Imola Ceramic Tile has designed clip, which is a laying system which utilizes a porcelain stoneware assembled on a plastic frame with automatic lock, allows for installation with a few simple steps, without incurring the drawbacks mentioned above.
 

The company declares that: The Faenza Clip Tile ® ceramic systems are wear resistant, puncture and impact resistant, rot-proof and non-porous, ceramic products allow you to quickly obtain a good level of hygiene, variety of colors and formats make this a perfect material for design.

The ease of installation quick and easy, achieving an aesthetic result guaranteed, the simplicity of automatic coupling between the elements, makes the system suitable for Clip Tile floor heating.

 

Another great advantage of the system described is the ability to easily replace a single tile and reuse the entire floor with the installation without adhesives and fillers for joints.

 
The inconveniences are completely negated by this good product, because its installation does not produce waste or dirt of any kind in addition to being hypoallergenic and free of harmful emissions.
 

Ready to use, no technical time of taking the hill, and without the need for cleaning with a reaction to fire class Bfl S1 (European standard reduces the transmission of sound).

 

This system, which is based on the dry laying, without the use of adhesives, it is particularly suitable for all floors, is by putting it directly on the concrete slab, overlapping it is to old floors such as marble, granite, ceramic tiles, cooked, linoleum.

 

Finally, the final cleaning easy, shortens the construction of the floor compared to traditional methods with glue.

 

Faenza Clip Tile ® does not require expansion joints and, where it becomes necessary to disassemble the floor, you can make the disengagement and the subsequent reassembly of the pieces in their original position.

 
 
 

A clean carpet

 A few other cleaners leave this step, cause if they are not pre-vacuum, or they use their truck to do it they immediately begin to clog their machines filtere. Because their filter is clogged with more and more every spec they pick their big powerful truck is losing more and more suction.Lose more suction lose less of the water-soluble contaminants in your carpet, which was dissolved by water and chemicals they may be used verwijderd.Wanneer removing them less of these pollutants You not only let the first floor filler, but it leaves a residue that attracts more dirt to the area, so the recoil is much faster and last but not least the dry periods have increased by less suction.
  As a carpet owner, when we talk about carpet cleaning industry, it is very important to them, how a regular assignment of broad carpet cleaning services tampa.De Burns Clean Team is one of the famous carpet cleaning industries serving in Maricopa area for more than 40 jaar.De Burns Clean Team is focused on meeting the carpet manufacturer for carpet maintenance supplies or vans.He is IICRC Certified Master cleaning company with many years experience in cleaning and road to testen.De Burns Clean Team offers quality cleaning services with a broad guarantee all tijd.Deze services mainly include carpet cleaning, pet odor removal, anti-allergen cleaning, tile cleaning, upholstery cleaning and air duct cleaning reinigen.cleaning methods are generally based on the following criteria:
  As you can see something seemingly as simple as dry vacuuming is very important and can not be overgeslagen.We use Dyson vacuums only because time and time again over the past four years they have carried out the vacuum cleaner I have the opportunity to clean up after me realize had.Ik vacuuming the way we all of the edges and corners to do anywhere from 20-45 minutes, but it is only one of the things we do to you the most thorough cleaning on the planet.
  You can jump on line to find the best carpet cleaner or expert advice is offline. There are many cleaning venders. Many people who offer superior carpet, rug area, and upholstery cleaning, tile and wood floor cleaning , as well as water damage repair, both commercially and domestic.
  With this you can also hire a guide consumers need in getting free services to find the information.Je get much help from the guide as what all the dirt problems caused to your expensive carpet, tiles or guides about how to prevent mistakes while carpet cleaning carpet cleaners who know little will make the situation more worse for you and your carpet.you do not get attracted by the low cost cleaning, so you should not do it twice and the list of the questions you need to get a good carpet cleaning company .

Carpet Care

Carpets are much more than mere decoration – they are investments. A beautiful Oriental or Persian rug expensive is among some of the more expensive types of carpets and valuable people use in their home. It ‘important to take as many precautions as possible to ensure that these carpets last for years, as they can, in all reality, they become assets for a family and be passed down for generations.

There seems to be a myriad of carpet cleaning tips – some are true and others are false. Separate fact from fiction among the most common questions carpet cleaning will help yield the answer. For example, many people believe that rubbing a stain on a carpet to help it out faster, or prevent it from being grounded in the fabric. This is not true, the answer to this common carpet cleaning question is never, never scrub a stain no matter how bad the need may arise. Only spots stain.

When blotting stains the trick is to always start cleaning carpet stains as soon as it occurs. Take paper towels and apply pressure to the stain as much as possible.

Another common carpet cleaning question / myth is that using soap to clean carpets is safe for the same carpet. This is untrue. Never use soaps, detergents, especially not flat. The reason is because the soap requires a massive amount of water to wash off the carpet. If an individual the required amount of water used to wash off the soap from the carpet, then the carpet was soaked completely through. In addition, because most people are not able to completely abolish the soap from carpet after using a soap solution to clean stains, soap dries out and act as a collector of dirt – that shaved several years off life a carpet. The answer to this enigma of carpet cleaning is to use only water or club soda to pull stains out of carpet.

As for the soda club is concerned – that really works. This has been labeled by some as a myth, or an “old wife tale” and many owners are not sure if the carpet is actually a plausible solution to stains. However, using club soda to remove stains is actually a tried and true method that works for many types of carpet stains.

Perhaps one of the most dangerous notions about cleaning the carpet is that if it is a rug or carpet cleaner, then it is absolutely safe to use. The answer to this common carpet cleaning question is a big NO. Any rug or carpet cleaning machine is not safe for the carpet of a home. Only buy or rent carpet cleaners that are approved by Rug & Carpet Institute’s green seal of approval on the back. Always avoid food store carpet cleaners. The only safe carpet / carpet cleaners are “Oxy” -. Cleaners such as steam cleaners

Last but not least, the hot water is not suitable for use on carpets. People may think that the warmer the water, cleaning the stain. But this can actually cause a number of problems for most of the carpets. Use only lukewarm water when slightly absorbing stains.

Obviously, every type of carpet is different. There are oriental rugs, Persian rugs, braided rugs, shag rugs and carpet hearth. Be sure to try the style and fabric and the brand of carpet must be cleaned before risking the spread of the stain, the color fade or bleach-sensitive dyes into the carpet

Upholstery Cleaning

Among the housework is certainly the most tiring, upholstery cleaning, a task that takes a long time and do not always do the best you can, fortunately, however, there are several tricks that make this job a little ‘ lighter. As in many cases, even for upholstery cleaning you can use products that are on the market, or natural methods, let’s see both.

How to clean upholstery
To clean the upholstery on the market there are several specific products based on active oxygen, and work very simple: just sprinkle or pour about to be treated, let them work for a few minutes and then clean with a soft, dry cloth. These products are for all types of upholstery and are designed not to ruin even the most delicate fabrics, but if you’re not convinced to use chemical products or upholstery still in question are made of paper, we have to rely on natural methods.

How to clean upholstery with natural methods
To clean the upholstery fabric, such as sofas or curtains cover you can use a mixture of water, baking soda and salt, rub gently to just a few minutes and the stain will go away, then dried with a hair dryer set to a medium temperature.

As for the tents, which are generally made with very delicate materials, if the stains and dirt are caused by mold and fumes of the kitchen, just put them to soak in a bowl with cold water and white vinegar in the proportion two cups of vinegar to two gallons of water, let them soak for a while ‘and then transfer them into a bowl with water and mild softening, and finally rinsed: In addition to clean your blinds are also fragrant.

The upholstery of paper
There are many types of upholstery, paper ones are the most common and among them there are different types, let us see what are the best ways to clean them.

The wallpaper is not washable
The wallpaper is not washable should not be washed with water, otherwise they lose the color, the only solution in case of dirt has to go through the gommapane, if more than dirt, then the problem is the grease past the iron on warm a sheet of wrapping paper and repeat the operation until the complete disappearance of the stain, then apply a spray solvent

Tile cleaning

A patch of tiles can often have a far greater visual effect of the tiles is limited a. Learn the best methods for cleaning of tiles and tile sealing to help prevent staining.
The tiles are a product commonly used in wet areas of the house. The bathrooms, kitchens, mudrooms and all inputs will use frequently tile floors, walls and backsplashes. Because each type of tile is different in its makeup, so is the protocol for cleaning, protecting and removing stains from each. Learn how to clean the tiles in each application to ensure its beauty and long life.
Natural stone tile cleaning
The marble tile cleaning or other natural stone tiles require some special care. Natural stones are porous, meaning that depending on the type of stone, the surface may be covered in millions of tiny holes, the most undetectable to the naked eye.
These tiny holes make natural stone tiles in a magnet for dirt, spills and stains. The natural stone materials also react differently to acids and alkalines, meaning that the wrong type of cleaner may do more harm than good to the stone, actually removing or covering its surface.

To care for natural stone should be sealed before filling with Malta as well as on an ongoing basis with a silicone-based, impregnating sealer. This sealer will fill the holes in the surface of the tiles and will help prevent staining. A tile should be sealed well water beading up off of its surface, if the water stops beading when cleaning is time to reseal the tiles.
The sealing of the tiles is done by dipping the brush in the foam liquid sealer and paint it on the tiles. Wait for a little while to soak in and then to clean on the excess with a white cloth that leaves no residue. The sealer may take the vapors or fumes, so be sure to install some form of ventilation.
To clean the natural stone tiles, stone or use a cleaner water and a mild solution of soap. Use a soft cloth and lint to avoid scratching the surface. If there are stains on the surface of stones, a poultice made specifically for stone tiles can be applied. The hard spots, after the spread of the poultice on the stone, cover with plastic wrap and allow to sit for up to several hours before cleaning it off. The poultice if the life out of most of the stain embedded.
If the surface of the tiles has to be brought, engraved or lose its shine, a shine-enhancing sealer can be applied to small areas. Large areas, however, should be refinished by a marble or a stone conservator.

Mudroom floor, atrium and basement

Glass tile cleaning
The glass brick tiles are among the easiest to care for. To clean the glass tile, glass cleaner or white vinegar can be used with a cloth that leaves no residue. Take care with the mosaic tiles that were hand cut, since the edges can be sharp and protrude a po’dalla surface.
In order to prevent stains and water spots in a shower, try using a squeegee to remove excess water on the tiles after the last user has finished showering that day. This method can also be used on shower doors to help prevent the accumulation of hard water.
Porcelain tile and ceramic tile cleaning
The porcelain tiles are non-porous, meaning it will not absorb stains or dirt and that they remain acce surface. The porcelain tile can be cleaned with any household cleaner, but if there is mixed in with the porcelain marble in a drawing mixed material, are safe to use a stone cleaner over the entire surface.
Ceramic tiles with a smooth, even icing will also be non-porous and easy to care for. If the surface of the icing is structured, however, or if the glaze has cracked or extra care â € ž € œfatta impazzireâ may be required.
Ceramic tiles can be structured more difficult to clean because no dirt or stains seeps into the tile, but because their structure can make it more difficult to reach the dirt or stains. For too hard to reach spots, a poultice can be used to pull the spots closer to the surface where they can be cleaned away.
Crackled Ceramic tiles have small cracks or crazed run through the glaze of the tiles. These cracks are straight through, meaning that the body of the clay and now it is exposed and vulnerable to dirt and stains. To help these stains, seal tiles that have crazy every time they are used in a wet area. The tiles made mad or Crackled should also be sealed before filling with mortar to keep the grout from entering the cracks.
All glazed ceramic tiles can go crazy over time, even if some tiles are more likely to do so than others. If cracks appear, apply a sealer as soon as possible impregnation. Besides, it is recommended to periodically reseal the tiles made mad, because more cracks may appear over time.
If the stains come into the cracks, it can be difficult to remove. Start with using a poultice to pull the spots in the area. The bleaching agent may also have some effect, if it worked far enough to reach into the cracks of the clay body to help lighten the stains. The best method of dealing with crazy tile is made to prevent the formation of the spots, it is always diligent about sealing of these tiles as cracks appear.
The tiles in wet areas or in high traffic areas may need more care than the tiles in dry wall applications. Prevention is always the best policy, so be sure to seal well tiles and clean them often to prevent stains series. Well cared for tiles and enjoy their beauty and long life for years to come.

 
 
 
 
 
 
 
Drag with shift key to reorder.
 

Carpet cleaning

The carpet cleaning is one way to remove dirt, debris and allergens from homes. Vacuuming and carpet steam cleaning helps maintain a healthy environment.

The conservation of domestic carpet clean is important to maintain a healthy environment. The allergen particles and dirt from carpets can enter the air quality of air that causes difficult, that can aggravate asthma, allergies and other breathing problems. The home of the carpet cleaning removes dirt, debris and allergens from the carpet fibers. Generally, the void covers on a regular basis, like once or twice a week, but the heavy traffic areas may need to vacuuming more often. If the carpet is very soiled, steam cleaning can be necessary.

Carpet vacuum

Before vacuuming carpets, make sure to remove all the clutter from carpets. CIA ² is particularly important in children’s bedrooms where small toys or parts of toys can dislodge carpet. Some small items such as paper clips, rubber bands and marbles can damage the vacuum.

Removing the loose dirt or soil that remains on the surface of the carpet prevents deep into carpet or included by foot traffic.

In vacuuming, use a slow, reflecting the forward movement that pushes the vacuum cleaner a few feet at a time, then reverse the direction. The vacuum cleaner will work more efficiently to remove dirt and allergens.

While vacuuming, if a spot is found, it is important groped Spotting the most quickly as possible. Usually, most long carpet stain remains, is more difficult to remove. If the liquid from the stain soaks into the carpet padding, mold can develop that can contribute to air quality difficult.

Carpet Steam Cleaning

The carpet steam cleaning is a way to deeply clean the carpet very dirty. Steam cleaning involves high temperature and pressure to clean the carpet. The purchase or rent a steam cleaner, sometimes referred to as wet-clean machine, a hardware store or grocery store, it will be necessary for the do-it-yourselfer. The professional carpet cleaning companies are available for people who want to deeply clean the carpet, but do not have the time for a project of carpet cleaning.

Spring Cleaning the carpet

Remove all the furniture before you begin the process of steam cleaning, so the entire carpet is available for cleaning.

Vacuuming the carpet before steam cleaning is important to remove all loose dirt and debris.

Pre-treat any stains on the carpet before you begin the process by steaming. Read the directions for the operation of the carpet steam cleaned and the carpet.

Allow at least 24 hours to dry before ¨ carpet to walk on it. If possible, open windows to allow air to circulate and help with the drying process, or turn on a fan to circulate air for drying more quickly.

Vacuuming and steam cleaning removes dirt, debris and allergens from the carpet fibers. © Since the carpet steam cleaning is the most time consuming vacuuming the carpet, many people choose to employ professional carpet cleaning company to steam clean. Keeping your home clean carpet vacuuming and regular cleaning of steam if needed will help maintain a healthy environment.